構築

現在、以下のコマンドを用いて生成したSDKを用いて開発を行っています。
bitbake -c populate_sdk [ターゲット名]

アプリケーションのビルドに関しては、このSDKさえあればビルド可能です。
現在新規driverをkernelとは別に作成しています。
driverのビルドに関しては、SDKのみの用意ではビルドできず、
kernelをbitbakeした上で、makefileに以下のように記載しビルドしています。
KERNELSRCDIR = ../../build-openstlinuxweston-xxx/tmp-glibc/work-shared/xxx/kernel-build-artifacts

現在driverのビルドに関しても、SDKのみで行う方法がないかと考えているのですが、そのようなことは可能でしょうか。

現在、RZ/G1CーPF評価ボードでYoctoの構築を行っているのですが、
bitbake core-image-westonコマンドを実行すると下記のエラーが発生し、
解消がなかなか難しい状態です。
問題点や解消方法をご存じの方がおられましたらお力添えいただけますと幸いです。

VirtualBox:~/iwg23s-release-bsp/build$ bitbake core-image-weston
Loading cache: 100% |########################################################################################| ETA: 00:00:00
Loaded 1801 entries from dependency cache.
NOTE: Resolving any missing task queue dependencies
NOTE: multiple providers are available for jpeg (jpeg, libjpeg-turbo)
NOTE: consider defining a PREFERRED_PROVIDER entry to match jpeg
NOTE: multiple providers are available for virtual/mesa (mesa, mesa-gl)
NOTE: consider defining a PREFERRED_PROVIDER entry to match virtual/mesa
NOTE: multiple providers are available for virtual/libgl (mesa, mesa-gl)
NOTE: consider defining a PREFERRED_PROVIDER entry to match virtual/libgl
NOTE: multiple providers are available for runtime libgl (mesa, mesa-gl)
NOTE: consider defining a PREFERRED_PROVIDER entry to match libgl
NOTE: multiple providers are available for jpeg-native (jpeg-native, libjpeg-turbo-native)
NOTE: consider defining a PREFERRED_PROVIDER entry to match jpeg-native

Build Configuration:
BB_VERSION = "1.22.0"
BUILD_SYS = "x86_64-linux"
NATIVELSBSTRING = "Ubuntu-14.04"
TARGET_SYS = "arm-poky-linux-gnueabi"
MACHINE = "iwg23s"
DISTRO = "poky"
DISTRO_VERSION = "1.6.1"
TUNE_FEATURES = "armv7a vfp neon callconvention-hard cortexa7"
TARGET_FPU = "vfp-neon"
meta
meta-yocto
meta-yocto-bsp = "tmp:c4f1f0f491f988901bfd6965f7d10f60cb94a76f"
meta-rzg1
meta-renesas = "<unknown>:<unknown>"
meta-oe = "tmp:dca466c074c9a35bc0133e7e0d65cca0731e2acf"
meta-linaro-toolchain = "tmp:8a0601723c06fdb75e62aa0f0cf15fc9d7d90167"

NOTE: Preparing runqueue
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
ERROR: Command Error: exit status: 1 Output:
error: patch failed: arch/arm/boot/dts/Makefile:180
error: arch/arm/boot/dts/Makefile: patch does not apply
error: arch/arm/boot/dts/r8a77470.dtsi: already exists in working directory
error: arch/arm/boot/dts/r8a77470-skrzg1c.dts: already exists in working directory
error: arch/arm/boot/dts/r8a77471.dtsi: already exists in working directory
error: arch/arm/boot/dts/r8a77471-skrzg1c.dts: already exists in working directory
error: patch failed: arch/arm/configs/shmobile_defconfig:20
error: arch/arm/configs/shmobile_defconfig: patch does not apply
error: patch failed: arch/arm/mach-shmobile/Kconfig:56
error: arch/arm/mach-shmobile/Kconfig: patch does not apply
error: patch failed: arch/arm/mach-shmobile/Makefile:20
error: arch/arm/mach-shmobile/Makefile: patch does not apply
error: patch failed: arch/arm/mach-shmobile/Makefile.boot:17
error: arch/arm/mach-shmobile/Makefile.boot: patch does not apply
error: arch/arm/mach-shmobile/pm-r8a7747x.c: already exists in working directory
error: arch/arm/mach-shmobile/r8a7747x.h: already exists in working directory
error: arch/arm/mach-shmobile/setup-r8a7747x.c: already exists in working directory
error: arch/arm/mach-shmobile/smp-r8a7747x.c: already exists in working directory
error: arch/arm/mach-shmobile/board-skrzg1c-reference.c: already exists in working directory
error: include/dt-bindings/clock/r8a7747x-clock.h: already exists in working directory
ERROR: Function failed: patch_do_patch
ERROR: Logfile of failure stored in: /home/protec/iwg23s-release-bsp/build/tmp/work/iwg23s-poky-linux-gnueabi/linux-iwg23s/3.10+git9c8ffcd274f74c4c4efecb307157ee4c6df54fa4-r0/temp/log.do_patch.10477
ERROR: Task 67 (/home/protec/iwg23s-release-bsp/build/../meta-renesas/meta-rzg1/recipes-kernel/linux/linux-iwg23s_3.10.bb, do_patch) failed with exit code '1'
NOTE: Tasks Summary: Attempted 736 tasks of which 735 didn't need to be rerun and 1 failed.
No currently running tasks (735 of 4433)

Summary: 1 task failed:
/home/protec/iwg23s-release-bsp/build/../meta-renesas/meta-rzg1/recipes-kernel/linux/linux-iwg23s_3.10.bb, do_patch
Summary: There were 2 ERROR messages shown, returning a non-zero exit code.

いつもお世話になっております。
現在、RenesasのRZG1C評価ボードでYoctoの構築を行っていおるのですが、
下記のようなエラーが発生しております。
修正方法や修正箇所等ご存知の方がおられましたらご助力いただけますと幸いです。

iwg23s-release-bsp/build$ bitbake core-image-weston
Loading cache: 100% |#################################################################################################################################| ETA: 00:00:00
Loaded 1801 entries from dependency cache.
WARNING: Unable to get checksum for uvcs-kernel-module SRC_URI entry uvcs-kernel.tar.bz2: file could not be found | ETA: --:--:--
WARNING: Unable to get checksum for vspm-kernel-module SRC_URI entry vspm-kernel.tar.bz2: file could not be found
WARNING: Unable to get checksum for mmngr-kernel-module SRC_URI entry mmngr.tar.bz2: file could not be found
WARNING: Unable to get checksum for mmngrbuf-kernel-module SRC_URI entry mmngrbuf.tar.bz2: file could not be found
WARNING: Unable to get checksum for fdpm-kernel-module SRC_URI entry fdpm-kernel.tar.bz2: file could not be found
WARNING: Unable to get checksum for s3ctl-kernel-module SRC_URI entry s3ctl-kernel.tar.bz2: file could not be found
WARNING: Unable to get checksum for gles-kernel-module SRC_URI entry SGX_KM_E2X.tar.bz2: file could not be found
WARNING: Unable to get checksum for gles-user-module SRC_URI entry r8a7747X_linux_sgx_binaries_gles2.tar.bz2: file could not be found
WARNING: Unable to get checksum for vspm-user-module SRC_URI entry vspm-user.tar.bz2: file could not be found
WARNING: Unable to get checksum for mmngrbuf-user-module SRC_URI entry mmngrbuf.tar.bz2: file could not be found
WARNING: Unable to get checksum for mmngr-user-module SRC_URI entry mmngr.tar.bz2: file could not be found
WARNING: Unable to get checksum for fdpm-user-module SRC_URI entry fdpm.tar.bz2: file could not be found################## | ETA: 00:00:00
WARNING: Unable to get checksum for s3ctl-user-module SRC_URI entry s3ctl.tar.bz2: file could not be found######################### | ETA: 00:00:00
WARNING: Unable to get checksum for omx-user-module SRC_URI entry RTM0AC0000XCMCTL20SL32C.tar.bz2: file could not be found################## | ETA: 00:00:00
WARNING: Unable to get checksum for omx-user-module SRC_URI entry RTM0AC0000XVCMND20SL32C.tar.bz2: file could not be found
WARNING: Unable to get checksum for omx-user-module SRC_URI entry RTM0AC0000XV264D20SL32C.tar.bz2: file could not be found
WARNING: Unable to get checksum for omx-user-module SRC_URI entry RTM0AC0000XV264E20SL32C.tar.bz2: file could not be found
WARNING: Unable to get checksum for omx-user-module SRC_URI entry RTM0AC0000XVCMNE20SL32C.tar.bz2: file could not be found

以上、何卒宜しくお願い致します。

現在構築したLinux上で
「iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT;」
を実行した所、
「iptables: No chain/target/match by that name.」
というエラーが発生しており実行できない状態です。

Linuxの構築はYocto2.2 core-image-minimalイメージをベースに行っており、
カーネルコンフィグレーションに以下の設定を追加しております。

設定を「y」にしているためカーネルモジュールは何も追加しておりません。
「 iptables -A INPUT -p tcp --dport 22 -j ACCEPT;」
などのTCPポート許可などは実行できている状態です。

何か他に足りない設定、モジュールなどがあるのでしょうか？

CONFIG_NETFILTER=y
CONFIG_NF_MATCH_STATE=y
CONFIG_NF_CONNTRACK=y
CONFIG_NF_TABLES=y
CONFIG_NETFILTER_XTABLES=y
CONFIG_IP_SET=y
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_MATCH_STATE=y
CONFIG_IP_NF_CONNTRACK=y
CONFIG_NF_CONNTRACK_IPV4=y

エラー解析のためにbitbakeで発生しているwarningの解析を行おうとしており、アドバイスいただければと思います。

STM32MP1+OpenSTLinuxにて、OSのバージョンをopenstlinux-20-02-19からopenstlinux-5.4-dunfell-mp1-20-11-12に変更したところ、実行時にいくつかのエラーが発生しました。
そのうちkernelが起動時に以下のエラーを表示し止まる点について解析しています。
[ 2.484038] Warning: unable to open an initial console.
[ 2.491657] Freeing unused kernel memory: 1024K
[ 2.496587] Run /init as init process
[ 2.853719] udevd[147]: Starting version 244.3+
[ 2.879007] udevd[148]: /lib/udev/rules.d/50-udev-default.rules:18 Unknown group 'tty', ignoring
[ 2.901279] udevd[148]: /lib/udev/rules.d/50-udev-default.rules:19 Unknown group 'tty', ignoring

同イメージをbitbake時に以下のwarningが表示されており、関連性を疑っています。
WARNING: st-image-vendorfs-1.0-r0 do_image: /vendor folder not available in rootfs folder, no reformat done...
WARNING: st-initrd-1.0-r0 do_package: Manifest build-openstlinuxweston-stm32mp1-portsetting/tmp-glibc/sstate-control/manifest-x86_64_x86_64-nativesdk-st-image-resize-initrd.packagedata not found in stm32mp1_202102 cortexa7t2hf-neon-vfpv4 cortexa7t2hf-neon cortexa7t2hf-vfp cortexa7hf-neon-vfpv4 cortexa7hf-neon cortexa7hf-vfp armv7vet2hf-neon-vfpv4 armv7vehf-neon-vfpv4 armv7vet2hf-neon armv7vehf-neon armv7vet2hf-vfp armv7vehf-vfp armv7at2hf-vfp armv7ahf-vfp armv6thf-vfp armv6hf-vfp armv5tehf-vfp armv5ehf-vfp armv5thf-vfp armv5hf-vfp allarch x86_64_x86_64-nativesdk (variant '')?

ビルドのために使用しているレシピはst-image-core.bbとほぼ同一であり、SUMMARYとLICENSEのみ記載を変更しています。

bitbake側から本エラーについて解析を試みれないかと考えているのですが、どのファイルの参照や操作をすればよいかがわかりません。
初歩的な質問かもしれませんが、アドバイスいただけますでしょうか。

windows10パソコン + VirtualBox6.1 + CentOS7.9.2009 で、実験しています。

https://www.aps-web.jp/academy/wr-linux/18676/#YoctoLinuxWind_River_Linux
の中にある、
bitbakeコマンドでLinuxディストリビューションをビルドする
bitbake wrlinux-image-glibc-std -c populate_sdk_ext
をやると、容量不足で失敗します。（開始後７～８時間後くらいと思われる）
No new taks can be executed since the disk space monitor action is "STOPTASKS"!
というメッセージが出ます。

dfをやると、

-------------------------------------- 以下、df結果抜粋 ----------------------------------------
ファイルシス 1K-ブロック 使用 使用可 使用% マウント位置

/dev/mapper/centos-root 52403200 5643500 46759700 11% /
/dev/mapper/centos-home 46237636 45283004 954632 98% /home

total 110309200 51222420 59086780 47% -
-------------------------------------- 以上、df結果抜粋 ----------------------------------------

という結果になるので足りていると思うのですが、足りないのでしょうか？

宜しくお願い致します。

現在、microchip社のATWILC1000の無線LANモジュールでWILC SDIOドライバを使用しております。
Linuxの構築はYocto2.2 core-image-minimalイメージをベースに行っております。

現在はWILC SDIOドライバをカーネル起動時にドライバのロードは出来ているのですが、
「modprobe wilc-sdio」でのドライバの再読み込みが出来ません。
これを有効にするには何か追加の設定などいるのでしょうか？

カーネルコンフィグレーションは以下の設定にしております。

CONFIG_CFG80211=y
CONFIG_WILC=y
CONFIG_WILC_SDIO=y
#CONFIG_WILC_SDIO=y
# CONFIG_WILC_HW_OOB_INTR is not set
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
CONFIG_CPUFREQ_DT=y
# CONFIG_ARM_KIRKWOOD_CPUFREQ is not set
CONFIG_ARM_OMAP2PLUS_CPUFREQ=y
CONFIG_ARM_TI_CPUFREQ=y
# CONFIG_QORIQ_CPUFREQ is not set
CONFIG_CPU_IDLE=y
# CONFIG_CPU_IDLE_GOV_LADDER is not set
CONFIG_CPU_IDLE_GOV_MENU=y
CONFIG_DT_IDLE_STATES=y
CONFIG_ARM_CPUIDLE=y
CONFIG_CPU_PM=y
# CONFIG_CPU_THERMAL is not set
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
# CONFIG_SUSPEND_SKIP_SYNC is not set
CONFIG_PM_SLEEP=y
# CONFIG_PM_AUTOSLEEP is not set
CONFIG_PM_WAKELOCKS=y
CONFIG_PM_WAKELOCKS_LIMIT=50
CONFIG_PM_WAKELOCKS_GC=y
CONFIG_PM_TEST_SUSPEND=y
CONFIG_PM_SLEEP_DEBUG=y
CONFIG_VT_CONSOLE_SLEEP=y
CONFIG_CPU_FREQ_GOV_ATTR_SET=y
CONFIG_CPU_FREQ_GOV_COMMON=y
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPUFREQ_DT_PLATDEV=y
CONFIG_PM_OPP=y
CONFIG_MAC80211=y
# CONFIG_WLAN_VENDOR_ADMTEK is not set
# CONFIG_WLAN_VENDOR_ATH is not set
# CONFIG_WLAN_VENDOR_ATMEL is not set
# CONFIG_WLAN_VENDOR_BROADCOM is not set
# CONFIG_WLAN_VENDOR_CISCO is not set
# CONFIG_WLAN_VENDOR_INTEL is not set
# CONFIG_WLAN_VENDOR_INTERSIL is not set
# CONFIG_WLAN_VENDOR_MARVELL is not set
# CONFIG_WLAN_VENDOR_MEDIATEK is not set
# CONFIG_WLAN_VENDOR_RALINK is not set
# CONFIG_WLAN_VENDOR_REALTEK is not set
# CONFIG_WLAN_VENDOR_RSI is not set
# CONFIG_WLAN_VENDOR_ST is not set
# CONFIG_WLAN_VENDOR_TI is not set
# CONFIG_WLAN_VENDOR_ZYDAS is not set
# CONFIG_CLOCK_THERMAL is not set
CONFIG_FIRMWARE_MEMMAP=y
# CONFIG_BIG_KEYS is not set
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_RNG=y
CONFIG_CRYPTO_RNG_DEFAULT=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_GF128MUL=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_CCM=y
CONFIG_CRYPTO_GCM=y
CONFIG_CRYPTO_SEQIV=y
CONFIG_CRYPTO_CTR=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_GHASH=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_ARC4=y
CONFIG_CRYPTO_DRBG_MENU=y
CONFIG_CRYPTO_DRBG=y
CONFIG_CRYPTO_JITTERENTROPY=y
CONFIG_PPP=y
# CONFIG_PPP_BSDCOMP is not set
# CONFIG_PPP_DEFLATE is not set
CONFIG_PPP_FILTER=y
# CONFIG_PPP_MPPE is not set
CONFIG_PPP_MULTILINK=y
CONFIG_PPPOE=y
CONFIG_PPP_ASYNC=y
# CONFIG_PPP_SYNC_TTY is not set
# CONFIG_SLIP is not set
CONFIG_SLHC=y

以下の設定を「m」にしてもmodprobe出来ませんでした。
CONFIG_WILC=m
CONFIG_WILC_SDIO=m

　https://www.aps-web.jp/academy/wr-linux/23638/
　Wind River LinuxでLinuxディストリビューションとSDKをビルドする
の作業をしているのですが、

bitbake wrlinux-image-glibc-std -c populate_sdk
のところで、
bash: bitbake: command not found
というのが出てきます。

この事前の作業で、
git clone git://git.yoctoproject.org/poky
をやって、その後、echo $PATHをやると、
/poky/bitbake/bin
が含まれた形で結果が返ってきます。

bitbakeを使える状態にするにはどうしたらよいのでしょうか？

宜しくお願い致します。

Yoctoのイメージ作成をおこなっているのですが、bitbake core-image-westonで
エラーが発生してしまいました。

ログは下記の通りです。
何かお分かりの方がおられましたら修正方法について
ご教示いただけますと幸いです。

$ bitbake core-image-weston
Loading cache: 100% |###############################################################################| Time: 0:00:01
Loaded 3036 entries from dependency cache.
NOTE: Resolving any missing task queue dependencies

Build Configuration:
BB_VERSION = "1.36.0"
BUILD_SYS = "x86_64-linux"
NATIVELSBSTRING = "universal"
TARGET_SYS = "arm-poky-linux-gnueabi"
MACHINE = "aprzg0a"
DISTRO = "poky"
DISTRO_VERSION = "2.4.2"
TUNE_FEATURES = "arm armv7ve vfp neon callconvention-hard cortexa7"
TARGET_FPU = "hard"
SOC_FAMILY = "rzg1:r8a7745"
meta
meta-poky
meta-yocto-bsp
meta-rzg1
meta-linaro-toolchain
meta-optee
meta-oe
meta-multimedia
meta-python
meta-networking
meta-qt5
common
qt-hmi-demo = "<unknown>:<unknown>"

Initialising tasks: 100% |##########################################################################| Time: 0:00:20
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
WARNING: qt5-launch-demo-1.0-r0 do_fetch: Failed to fetch URL http://www.renesas.com/jp/ja/img/products/media/auto-j/microcontrollers-..., attempting MIRRORS if available
ERROR: qt5-launch-demo-1.0-r0 do_fetch: Fetcher failure: Fetch command export DBUS_SESSION_BUS_ADDRESS="unix:abstract=/tmp/dbus-CBnDjtKUHM"; export SSH_AUTH_SOCK="/run/user/1000/keyring/ssh"; export PATH="/home/guest/user_work/build/tmp/sysroots-uninative/x86_64-linux/usr/bin:/home/guest/user_work/poky/scripts:/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/qt5-launch-demo/1.0-r0/recipe-sysroot-native/usr/bin/arm-poky-linux-gnueabi:/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/qt5-launch-demo/1.0-r0/recipe-sysroot/usr/bin/crossscripts:/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/qt5-launch-demo/1.0-r0/recipe-sysroot-native/usr/sbin:/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/qt5-launch-demo/1.0-r0/recipe-sysroot-native/usr/bin:/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/qt5-launch-demo/1.0-r0/recipe-sysroot-native/sbin:/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/qt5-launch-demo/1.0-r0/recipe-sysroot-native/bin:/home/guest/user_work/poky/bitbake/bin:/home/guest/user_work/build/tmp/hosttools"; export HOME="/home/guest"; /usr/bin/env wget -t 2 -T 30 -nv --passive-ftp --no-check-certificate -P /home/guest/user_work/build/downloads 'http://www.renesas.com/jp/ja/img/products/media/auto-j/microcontrollers-... --progress=dot -v failed with exit code 4, output:
--2021-02-02 11:52:47-- http://www.renesas.com/jp/ja/img/products/media/auto-j/microcontrollers-...
Resolving www.renesas.com (www.renesas.com)... 23.9.173.129
Connecting to www.renesas.com (www.renesas.com)|23.9.173.129|:80... connected.
HTTP request sent, awaiting response... Read error (Connection timed out) in headers.
Retrying.

--2021-02-02 11:53:18-- (try: 2) http://www.renesas.com/jp/ja/img/products/media/auto-j/microcontrollers-...
Connecting to www.renesas.com (www.renesas.com)|23.9.173.129|:80... connected.
HTTP request sent, awaiting response... Read error (Connection timed out) in headers.
Giving up.

ERROR: qt5-launch-demo-1.0-r0 do_fetch: Fetcher failure for URL: 'http://www.renesas.com/jp/ja/img/products/media/auto-j/microcontrollers-.... Unable to fetch URL from any source.
ERROR: qt5-launch-demo-1.0-r0 do_fetch: Function failed: base_do_fetch
ERROR: Logfile of failure stored in: /home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/qt5-launch-demo/1.0-r0/temp/log.do_fetch.3211
ERROR: Task (/home/guest/user_work/build/../meta-rzg-demos/meta-rzg1/qt-hmi-demo/recipes-qt/examples/qt5-launch-demo_1.0.bb:do_fetch) failed with exit code '1'
NOTE: Tasks Summary: Attempted 3317 tasks of which 3124 didn't need to be rerun and 1 failed.

Summary: 1 task failed:
/home/guest/user_work/build/../meta-rzg-demos/meta-rzg1/qt-hmi-demo/recipes-qt/examples/qt5-launch-demo_1.0.bb:do_fetch
Summary: There was 1 WARNING message shown.
Summary: There were 3 ERROR messages shown, returning a non-zero exit code.

以上、何卒よろしくお願いいたします。

現在、RenesasのRZG1Eの評価ボードでYoctoの構築を行っているのですが、
bitbake core-image-westonを実行した際にエラーが発生してしまいます。
解消のためご助言をいただけましたら幸いです。
実行時のログは下記のとおりです。
$ bitbake core-image-weston
Loading cache: 100% |##############################################################| Time: 0:00:01
Loaded 3036 entries from dependency cache.
NOTE: Resolving any missing task queue dependencies

Build Configuration:
BB_VERSION = "1.36.0"
BUILD_SYS = "x86_64-linux"
NATIVELSBSTRING = "universal"
TARGET_SYS = "arm-poky-linux-gnueabi"
MACHINE = "aprzg0a"
DISTRO = "poky"
DISTRO_VERSION = "2.4.2"
TUNE_FEATURES = "arm armv7ve vfp neon callconvention-hard cortexa7"
TARGET_FPU = "hard"
SOC_FAMILY = "rzg1:r8a7745"
meta
meta-poky
meta-yocto-bsp
meta-rzg1
meta-linaro-toolchain
meta-optee
meta-oe
meta-multimedia
meta-python
meta-networking
meta-qt5
common
qt-hmi-demo = "<unknown>:<unknown>"

Initialising tasks: 100% |#########################################################| Time: 0:00:14
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
ERROR: v4l-utils-1.12.3-r0 do_compile: oe_runmake failed
ERROR: v4l-utils-1.12.3-r0 do_compile: Function failed: do_compile (log file is located at /home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/v4l-utils/1.12.3-r0/temp/log.do_compile.2615)
ERROR: Logfile of failure stored in: /home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/v4l-utils/1.12.3-r0/temp/log.do_compile.2615
Log data follows:
省略
cec-follower.o cec-follower.cpp
| arm-poky-linux-gnueabi-g++: error: cec-follower.cpp: No such file or directory
| arm-poky-linux-gnueabi-g++: fatal error: no input files
| compilation terminated.
| Makefile:556: recipe for target 'cec-follower.o' failed
| make[3]: *** [cec-follower.o] Error 1
| make[3]: Leaving directory '/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/v4l-utils/1.12.3-r0/build/utils/cec-follower'
| Makefile:468: recipe for target 'all-recursive' failed
| make[2]: *** [all-recursive] Error 1
| make[2]: Leaving directory '/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/v4l-utils/1.12.3-r0/build/utils'
| Makefile:574: recipe for target 'all-recursive' failed
| make[1]: *** [all-recursive] Error 1
| make[1]: Leaving directory '/home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/v4l-utils/1.12.3-r0/build'
| Makefile:501: recipe for target 'all' failed
| make: *** [all] Error 2
| ERROR: oe_runmake failed
| WARNING: exit code 1 from a shell command.
| ERROR: Function failed: do_compile (log file is located at /home/guest/user_work/build/tmp/work/cortexa7hf-neon-poky-linux-gnueabi/v4l-utils/1.12.3-r0/temp/log.do_compile.2615)
ERROR: Task (/home/guest/user_work/build/../meta-openembedded/meta-oe/recipes-multimedia/v4l2apps/v4l-utils_1.12.3.bb:do_compile) failed with exit code '1'
NOTE: Tasks Summary: Attempted 3279 tasks of which 3278 didn't need to be rerun and 1 failed.

Summary: 1 task failed:
/home/guest/user_work/build/../meta-openembedded/meta-oe/recipes-multimedia/v4l2apps/v4l-utils_1.12.3.bb:do_compile
Summary: There were 2 ERROR messages shown, returning a non-zero exit code.
以上、何卒よろしくお願いいたします。